Looking for:
Kubota: SVL Work Shop Manual, Part # RY |
Kubota svl75-2 manual
Telephone : Western Division : S. Guild Avc. S , Rue Jules Vercruysse, Z. Engine exhaust, some of its constituents, certain vehicle components and fluids, contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
The symbols are shown below with an indication of their meaning. It is made of fine materials and under a rigid quality control system. It will give you long, satisfactory service. To obtain the best use of your machine, please read this manual carefully. It will help you become familiar with the operation of the machine and contains many helpful hints about machine maintenance.
The immediate use of new techniques in the manufacture of products may cause some sections of this manual to become outdated.
Please do not hesitate to consult with them. Read these instructions carefully. It is essential that you read the instructions and safety regulations before you attempt to assemble or use this unit. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. Read and understand this section carefully, before operating the machine. Every user, however experienced, should carefully read and understand this section and those of the attachments and accessories before taking the machine into operation. The owner is obliged to inform the operators of these instructions in detail. Keep this manual in the storage place.
The seat belt must be inspected regularly and replaced if frayed or damaged. Know your equipment and its limitations. Read and understand this entire manual before attempting to start and operate the machine. Obey the danger, warning and caution labels on the machine. Do not modify structural members of ROPS by welding, drilling, bending, grinding or cutting, as this may weaken the structure.
If any component is damaged, replace it. Do not attempt repairs. If the ROPS is loosened or removed for any reason, make sure all parts are reinstalled correctly. Tighten mounting bolts to proper torque. Do not operate the machine while under the influence of alcohol, medication, controlled substances or while fatigued.
Check the surrounding area carefully before using the machine or when attachments are being connected. To avoid any danger of electrocution, never operate the machine near power lines before confirming the power is off and all local and national safety regulations.
Never approach a machine or load that is contacting a power source such as power lines. Electrocution can occur by coming into contact with a machine that is near power lines. Check for buried pipes and cables before digging.
Check for hidden holes, obstacles, soft underground, and overhangs. Do not enter soft ground. A During machine use, do not allow any persons within the working range. Do not wear baggy, torn or oversized clothing when working with the machine as such clothing can get caught in rotating parts or control elements which can cause accidents or injuries. Wear adequate safety clothing, e. Do not allow passengers to ride on any part of the machine at any time.
The operator must remain in the machine seat during operation. Check the levers, pedals and mechanical parts for correct adjustments and wear. Replace worn or damaged parts immediately. Check the nuts and bolts regularly for correct torque. Keep your machine clean. Heavy soiling, grease, dust and grass can cause fires, accidents or injuries.
Before starting the machine, be absolutely sure that the machine has been filled with fuel, lubricated, greased and undergone all necessary maintenance. Do not modify the machine, otherwise it could lead to unforeseen safety problems. Make sure attachments, particularly those utilizing quick-hitch, are securely mounted.
Mount and dismount the machine safely. Always face the machine. Always use handrails and available steps and keep yourself well balanced. Do not grab or hold any of the control levers and switches. Do not jump on or off the machine, whether stationary or in motion. Always thoroughly check the surrounding area for any possible conditions that could create a dangerous situation. A To avoid damage and to prevent accidents, always use the buddy system and have the other person, check for clearances and other possible dangers that may be obstructed from view.
A Never allow people to approach the vicinity of the turning radius of the machine. A Be cognizant of blind spots to the rear and always check behind you before backing up. Only operate the machine in well-ventilated area to avoid poisoning from carbon monoxide, an odorless, colorless gas that is deadly.
Never remove any of the safety features on the machine. A Make sure all safety features, including guards, protective devices, doors and cabin, are functioning normally, properly secured and in good condition. Repair and replace any lost or damaged protective features.
Make sure you use them properly. A Make sure all safety features are in good operating condition and remove only when repair is needed. Always keep the heavy end of the machine up when traveling up or down an incline to avoid any possibility of machine rolling over. Place that bucket at a distance of 20 to 30 cm 8 to 12 in. Be prepared to lower the bucket to the ground in case of emergency.
To avoid injury or accidents, always operate the machine or the equipment at slow speed when going up or down an incline by reducing the engine speed rpm. Place the stroke of the left control lever at half speed or less when going down an incline. Traveling too fast down an incline can cause the operator to lose control of the machine. Avoid stopping suddenly on an incline, which can cause the machine to become unstable and rollover. Never cross an incline horizontally or at an angle, which can cause the machine to rollover.
Approach inclines vertically to avoid loss of control. Take care when moving the machine in slippery or unstable surfaces such as grass, fallen leaves, metal plates, or ice, as it may skid out of control.
Do not allow the machine to be oriented diagonally to such surfaces. Watch where you are going at all times. Watch for and avoid obstacles. Remain alert for trees, wires and other obstructions. Avoid any sudden movements while moving and operating the machine such as stopping, starting or turning.
Do not raise armrests while the machine is in motion as this will cause the parking brake to engage and could cause an accident or injury. Avoid driving the machine over any obstacles, which could cause loss of control.
If an obstacle cannot be avoided, always place the bucket close to the ground and move slowly over the obstacle. Do not approach an obstacle at an angle, which could cause the machine to rollover. Avoid performing any work with the machine when it is on an incline, which could cause it to become unbalanced and rollover. Always take care when moving the machine on an incline. Always make sure the heavy end of the machine is facing up the incline when moving it up or down the incline.
Always use caution when floating the lift arms. A Always make sure the bucket is lowered to the ground before floating the lift arms. Floating the lift arms when the bucket is raised could cause an accident or injury from the bucket falling. Always operate the machine at low speed, carefully checking the area in front of the load you will be moving.
Never operate the machine with the bucket raised over the heads of people. Accident or injury may occur from objects falling from the bucket or the bucket itself falling. Beware of material falling from the bucket. Unstable material in the bucket such as round, cylindrical, or stacked items could fall from the bucket, causing injury.
Always move an unstable load with the bucket lowered. Any sudden movements of the machine such as lowering or stopping of the attachment may cause it to recoil and rollover. Pay particular attention when the bucket is loaded. Never exceed the maximum loading capability of the bucket or put loads off-center of the bucket, which can cause the machine to become unstable and rollover.
No comments:
Post a Comment